Printhead 950 951 Fit HP Officejet Pro 8600 8610 8620 8630 8640 251DW

Description: {{#imageLiProduct Description950 951 Printhead For HP Officejet Pro 8600 8610 8620 8630 8640 251DW Product Description ● Condition: Open box“New machine disassembled parts” ● Feature: Excellent performance and high quality. Made of high-quality material, durable, firm and stable for us to use. This is a cleaned, thoroughly tested and sealed Printhead. Good stability, long lifespan. Full color function. Size:104x90MM ● Compatible with: For Hp officejet pro 8100 For Hp officejet pro 8600 For Hp officejet pro CM751 For Hp officejet pro CM752 For Hp officejet pro N811A For Hp officejet pro 251dw For Hp officejet pro 276dw For Hp officejet pro 8610 For Hp officejet pro 8620 For Hp officejet pro 8630 For Hp officejet pro 8640 Before you buy this product, you need to pay attention to: NOTE: The printer must be disconnected from the power source before the print head is installed, otherwise it has the risk of causing the print head circuit board to burn out. 1. When the print head is shipped, a protective liquid will be applied to the print head. Before using it for the first time, wipe the print head before installing it.Just wipe the copper sheet gently, wipe it clean with soft paper, dont wipe it with cleaning fluid or eraser. 2. During the regeneration process of the print head, the ink will be cleaned and the protection liquid will be injected. If there is no protective liquid, the print head cannot print because the pipeline channel is dry.If the print head can be detected, but the colors are uneven or blurred, you can continue printing with ink. Print a few more sheets of paper and wait for the excess protection fluid to run out, then you can print normally 3. If the printing effect is not clear, press the machine cleaning button to clean (the print head must be cleaned only when the ink cartridge is sufficient, or it will burn out easily). 4. You dont need to clean the print head with cleaning fluid, you can clean the print head directly on the machine. If you clean the print head with the cleaning fluid(or water) and do not drop the protective fluid, the print head will be completely blocked, and it will be useless. Before you install this product, you need to pay attention to: 1.After receiving the print head, if you use a needle tube to inject water to check the nozzle or see if it is blocked, this is a very redundant and dangerous behavior.If the printing effect is not clear, press the machine cleaning button (the pFirst of all, once the print head enters the water, if the water is not dry, it is powered on. The main board will be burned out, and the print head will be burnt out. Secondly, the print heads sold in our shop have been strictly tested and filled with protective liquid.If you use a needle to inject water into the print head, it will not only wash away the protective liquid in the head, but also easily cause air blockage in the print head, resulting in no ink. 2.Be careful when installing the print head, be sure to cut off the power first, and install it in place. 3.When connecting the plug cable, do not have ink on it, and make sure that it is in good contact with the socket. 4.The steel shaft should also be clean and smooth. You can use a paper towel to stick some lubricating oil to wipe it. Do not directly add oil to the shaft. The excess oil will flow to the print head and cause damage. 5.After the machinery and circuit are all correct, check the water circuit. Firstly, check whether the ink volume in the ink cartridge is sufficient; secondly, check whether the small cleaning blade and the ink suction pump are dirty. 6.There will be air in the newly installed print head, so it will not print normally immediately. The printer can only produce perfect results after the air in the head is completely discharged.You can use the machines own cleaning function for intermittent cleaning(Clean 2 times each time, and then 2 times after 30 minutes) Repeated over-cleaning will cause ink accumulation in the cleaning pump, which will not only cause color mixing, ink leakage, and waste ink.Finally, you can print more pictures to let the print head exhaust air during work. Package included: 1 x Printhead Notice：1. If you are not completely satisfied with your purchase, you may return it for a refund or exchange it for a replacement. We only require that you contact us within 14 days of receiving your item and return it in the same condition it was received. 2.Please check the model before your purchase and compare the position of the screw hole In case of wrong purchase. 3.If you have any questions, please contact us by email and we will solve them for youAbout UsShippingReturnsFeedbackIf youre looking to buy in bulk or looking for a long term part supplier, please contact me directly. We will provide you the best products and service. Put off your doubts and fears and thusrest assured purchase. We offer 100% Customer Satisfaction , if you have any questions , please let us know and we will do our best to rectify the situation . We fully stand behind with all the items that we are selling ! When you receive your item , please leave positive feedback , we rely on you for our good name

Price: 125 USD

Location: Fremont, California

End Time: 2024-02-22T08:00:33.000Z

Shipping Cost: 0 USD