Happymodel Mobeetle6 whoop and toothpick 2-IN-1 FPV racer drone

Description: The DiamondF4 Flight controller and The Mobeetle6 were inspired from Angry Don FPV, we really appreciated for his help to Happymodel and to this hobby. We also very expecting to the performance of this BNF with the new Diamond F4 ELRS flight controller. Specifications:Brand Name: HappymodelItem Name: Mobeetle6 whoop and toothpick 2-IN-1 FPV Racer DroneWheelbase: 65mmSize: 80mm*80mm*30mmWeight: 17.5g (without battery) Features:The lightest 1S Whoop and Toothpick 2-IN-1 fpv droneComes with tooth pick frame for convertPowerful and efficiencyThe lightest 1s AIO 5IN1 F4 flight controllerNew Unibell SE0702 brushless motors with pcb wire board Built-in OPENVTX up to 400mwLow profile Canopy designPackage includes: Item Name Qty 65mm whoop Frame (Mobula6 frame)1 65mm toothpick frame(Mobeetle6 frame)1 Option1: DiamondF4 ELRS built-in SPI ELRS receiver1 Option2: DiamondF4 FR built-in SPI FRSKY receiver SE0702 KV23000 Unibell brushless motor4 Gemfan 1210 31mm propeller(4cw+4ccw)1 Runcam Nano31 Built-in 5.8G 48ch 25mw-400mw OPENVTX1 1s 300mah Lipo battery 2 Mobula6 canopy1 Propeller disassemble tool1 Screwdriver1 Spare parts specifications:Motor Mode:SE0702 KV23000Configu-ration:9N12PStator Diamter:7mmStator Length:2mmShaft Diameter:Φ1mmMotor Dimension(Dia.*Len):Φ9.5mm*14mmWeight(g):1.5gNo.of Cells(Lipo):1S onlyPropeller Weight:0.19gMaterial:PCPitch:1 inch Props Dia:30mmCenter Hole Dia:1mmFlight controller (ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280 (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FRMCU:STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection)Original whoop size compatiblePower supply: 1S battery input (DC 2.9V-4.35V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 readyBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G OPEN VTXBuilt-in SPI ELRS V2.0/Frsky receiverBuilt-in 5V 1A BECOnboard 4in1 ESC MCU upgraded to EFM8BB21Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds)Support BLHeliSuite programmableFactory firmware: O_H_50_REV16_8.HEXDefault protocol: DSHOT600Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 50Hz/150Hz/250Hz/500HzExpressLRS Firmware version: V2.0RF Frequency: 2.4GHzAntenna : Enameled copper wire antennaTelemetry output Power: <12dBmReceiver protocol: SPI ExpressLRSCompatible with ExpressLRS V2.0 TX ModuleCouldn’t flash separately ExpressLRS firmwareOnboard Frsky SPI D8 receiver Version SPI BUS receiver Frsky D8 compatibleCompatible Non EU transmitter D8 model Channels: 8chFailsafe supportNo ground interference ( Transmitter and receiver 1 m from the ground): 200m~300mOnboard 5.8g OPENVTX Firmware version: OPENVTXSmartaudio v2.1PIT Mode supportRCE Mode supportChannels:48chTransmitting Power: 0/RCE/25mw/100mw/400mwPower supply: DC 5VCurrent (5v): <650ma (400mw)Runcam Nano3 Model: RunCam Nano 3 Image Sensor: 1/3" CMOS Horizontal Resolution: 800TVL Lens : 2.3mm(M6.5) FOV 140° Signal System: NTSC S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: 0.01Lux@1.2F D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: 110mA@5V 120mA@3.3V Housing Material: ABS Net Weight: 1.2g Dimensions: L14mm*W14mm*H9mmLipo Battery Capacity:300mAhVoltage:3.8vContinuous Discharge Rate: 30CSize: 57mmx12mmx7mmWeight: 7.5g Connector: PH2.0

Price: 145.74 USD

Location: 深圳

End Time: 2024-03-09T07:38:34.000Z

Shipping Cost: 0 USD