Description: DIGITAL THERMATIC® FAN SWITCH WITH 1/4" NPT THERMAL SENSOR KIT & INLINE ADAPTER KIT (PART #0445 + #0409) This is a combo kit which includes Davies Craig parts:Digital Thermatic® Fan Switch with 1/4" NPT Thermal Sensor Kit (0445)Temperature Sensor Kit (Part #0409) 24 Volt ApplicationKit sold in 12-volt configuration, for 24-volt application, you will need to purchase 2 x 24-volt relays.Simply search our store for part 10534 combo components Digital Thermatic® Fan Switch with 1/4" NPT Thermal Sensor Kit (Part #0445) Temperature Sensor Kit (Part #0409) Description Qty Description Qty Digital Thermatic Fan Switch 1 In-Line Adaptor 35mm 1 Temperature Probe Sensor 1 EWP 3mm Sleeve Adaptor 2 ¼ NPT Thermal Sensor 1 Olive for 5mm Sensor 1 Temperature Probe Mounting Kit 1 Olive for 6mm Sensor 1 Blue 6mm Ring Terminals 1 Comp Fitting 6.35mm Sensor 1 Blue Connectors 1 Hose Clamps 2 Red 6mm Ring Terminals1 Instructions 1 Self-Tapping Screws 2 Davies Craig designed Digital Thermatic Fan Switch Kit can be used with Thermatic Fans, EWP's and competitors Fans. This kit comes with two sensors to enable various fitment options:Sensor 1: Temperature Probe (Air or Coolant Fitment)Sensor 2: ¼ NPT Thermal Sensor Kit (Coolant Fitment Only)Sensor 1: It senses air temperature as it passes through the radiator with the sensor placed in the radiator fin section or the sensor can also be placed directly into the coolant system in combination with the included Temperature Sensor Adapter Kit (Part 0409).Sensor 2: The Thermal Sensor can be placed into the thermostat housing, engine block, or directly into the radiator. If you would like to install this sensor in the top radiator hose, It can also be used with the included Temperature Sensor Adapter Kit (Part 0409). The Inline Sensor Adaptor simply fits into your engine’s top radiator hose. The adaptor ends for hose fitting are 35mm in size.With the use of our 3mm adaptor sleeve (Included in kit), this can be increased to 38mm (Part #18510)With the use of our 6mm adaptor sleeve (Optional), this can be increased to 41-42mm (Part #18511) It can run 1 or 2 fans and be used for 12 or 24 volt applications. It has an adjustable temperature range of 40ºC to 110ºC (104ºF to 230ºF) which can show Centigrade or Fahrenheit. Temp is set by pressing the set button. Fan #1 will start once the temperature reaches the set temperature. Fan #2 (if applicable) will start operation 10 seconds after fan #1 starts. The fan/s will operate until the temperature falls by 5°C below the set temperature.*Note: Kit sold in 12 volt configuration, for 24 volt application, you will need to change the two relays with 2 x 24 volt relays which are not supplied in the kit. We have 24 Volt relays listed on our store, part #0534 Sensor Wire length:142cm in total (Wire from switch 112cm plus sensor connector 30cm)Post 15-Dec-2021 = 320cm total (Wire from switch 290cm plus sensor connector 30cm)*The sensor wire has been increased to 320cm from the 15-Dec-2021, batch date 2021 IP66 Rated:Protected from total dust ingressProtected from high pressure water jets from any direction, limited ingress protectionNot waterproof Integrated electrical noise filter for improved compatibility and reliability in older vehicles that produce high levels of electrical interference and noise. SPECIFICATIONS Maximum voltage 15V *27V with 24V relays Maximum Current 40A Relay setup Dual relay Sensor Wire Length 142cm (Post 15-Dec-2021 320cm) Speed Single speed - 10 sec. delay to start Fan #2 Applications Recommended for all DCPL fans +2x14” HP & 2x16” Fans Temperature Display Red LED digital temp display – actual temp & set temp Red LED display Set display °C or °F Temperature settings 40°C to 110°C 104°F to 230°F Temp setting method Push Button Accuracy 99.9% Circuit type Pre-programmed micro controller Output wires Battery + Battery - IGN, AC Clutch Fan #1 & Fan #2 Temperature Probe & ¼” NPT Thermal Sensor Dimensions 95 x 65 x 56 mm *Note: if using this switch for use with and Electric Water Pump (EWP), it will not vary the speed of the pump in response to engine temperature but rather turn the pump on and off at your set temperature. For EWP control, Davies, Craig recommend the Digital Controller (Part 8002) which can manage both the EWP and your Thermatic Fans.
Price: 115.67 AUD
Location: Melbourne, Victoria
End Time: 2024-11-02T03:51:17.000Z
Shipping Cost: 55.09 AUD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 7 Days
Brand: Davies Craig Pty Ltd
Type: Electrical
Manufacturer Warranty: 3 Years
Manufacturer Part Number: 0445
Classic Part: Yes
Country/Region of Manufacture: Australia
Universal Fitment: Yes
Performance Part: Yes
