Description: About this Complete 1000W RMS Hi-Res Audio Front Stage 3-way component and Amplifier matched set.Critical MASS makes the worlds best and most expensive Car Audio system, the CES5.1 (see video attached for more information) This set utilizes one of the same amplifier used in the CES5.1 system but is matched with the best 3 way 1 ohm 6.5" component set by Critical MASS. This Hi-Res Audio 3 way component set was designed to mate with this 2 channel 1 ohm stable amplifier to make the ultimate Hi-Res 3-way front stage. You can look hi and low and you will not find a better Front Stage setup for your car. All components have been designed to work together to deliver the best and most powerful Audiophile grade Hi-Res 3-way component front stage in the world. This powerful Front Stage can be used as a complete audio system or with a subwoofer for a more powerful experience. This set comes with free expert US based technical support. About the 3 way 1 ohm Hi-Res Audio component setTechnical Specifications: Woofer Size: 6.5”, midrange Size 4", Tweeter Size 2" RMS Power handling:500 Watts per channel (150W - 500W RMS per channel is recommended)Sensitivity: 98db @ 2.83V Frequency Response:34-40,000 hzMotor Type: Internal NEO Magnet (TWEETER, MIDRANGE and WOOFER)Voice Coil Type: Ultra-High Temp Dual 2 ohm Coils SYSTEM Impedance: 1 ohm nominalCrossover Network: 3-way 24db/oct for ACTIVE 3 way component setup use 2 amplifiers Critical MASS 4CH amplifier model # ELS-1000.4 For active crossover set ELS-1000.4, front channels to 3Khz Hi-pass and connect to tweeters only. Set rear channels to 3Khz Lo-pass and connect to Woofers only. Critical MASS 2CH amplifier model # ELS-1000.2 For active crossover set ELS-1000.2, Band Pass Mode. set Hi Pass to 1Khz and set Lo Pass to 3Khz and connect to midranges only. ULTRA-PERFORMANCE 1 OHM DESIGN:This component kit is an Ultra-Performance 6.5" Component kit made to use every watt from your 1 ohm stable amplifierThis set handles up-to 7 times more power, has a considerably higher linear and maximum excursion, andaudibly lower distortion, while weighing as much as 66% less than the competition. HYBRID CARBON FIBER CONE:This cone is made of Lightweight rigid fiber and oversized real Carbon fiber cap to withstand more than 1000 Watts of peak music power.The Lightweight Carbon Fiber Cone hybrid increases rigidity, efficiency and clarity at all levels which ultimately means more, undistorted sound. Included in this pro 3way 1 ohm kit:Two 6.5" WoofersTwo 4" MidrangeTwo 2" TweetersTwo 24db/oct Crossover networks (3way)About the AmplifierThis compact true audiophile grade amplifier uses only MADE IN JAPAN audio components for the absolute best audio in a hybrid class D design. It gives the best of all worlds with high efficiency and amazing sound quality. Capable of being mated with all high end components in 2 channel or multi Amp bi-amped configurations. This amplifier is stable to 1.5 ohms when Bridged (up to 3 x 4 ohm speakers when bridged) will deliver 1000W RMS or when in stereo you can drive the amplifier down to 0.75 ohms per channel (up to 3 x 2 ohm speakers per channel) and it will deliver 500Watts RMS x 2 channels. There are no comparable amplifiers in the market today. Made in JAPAN audio components are one of the many features that sets this Critical Mass Audio 2 channel Amplifier apart. Features:Only Audiophile grade components with Audiophile tolerances for pure exact audio reproduction at all volume levels throughout the entire bandwidth.Frequency response 5Hz - 50KhzJAPAN made nichicon/rubycon capacitors and componentsHigh bandwidth amplifier sectionProtection and Power on indicator LEDAudiophile grade input with 9V - 0.1V Gain volume Min - MaxProtection circuit for thermal, overload, over voltage, DC reverse, - DV offset18 db/oct variable Hi-pass available on all channels18 db/oct variable Lo-pass available on all channels12 db/oct variable BAND-PASSFull range available on all channelsTrue Audiophile design for full range drivers and subwoofers alike High Efficiency Audiophile designOptional ( ELS BASS KNOB ) for remote Bass boost when used as a subwoofer amplifier only Specifications:All specifications at 14.6VPower at 0.75 ohm Stereo 500w x 2CH Power at 1 ohm Stereo 400w x 2CH(use 1 x Critical MASS 1ohm series Components per channel or 2 x Critical Mass 2 ohm Components or 4 x 4 ohm traditional speakers or components per channel to achieve 400w RMS per Channel)Power at 1.5 Ω Mono (Bridged) 1000w x 1 CH (use 3 x UL-SL12 DVC Subwoofes at 4 ohms each then all in parallel for 1.5 ohms )to power the UL12 (Use one ELS-1000.2 bridged per Voice Coil on the UL12 TO MEET THE RECOMENDED 2000w-2500watts min RMS for the UL12 )Power at 2 Ω Stereo 200w x 2 CH (use 1 x Critical MASS 2ohm series Components or 2 x 4 ohm traditional speakers or components per channel to achieve 200w RMS / Channel)Power at 4 ohms 100w x 2 CH High pass variable crossover(15Hz~3KHz at 18 db/oct - all channelsLow pass variable crossover(15Hz~3KHz at 18 db/oct - all channelsT.H.D. at 4 ohm rated 0.001%Input sensitivity 100mV~9VInput impedance 120K ΩDamping factor >800S/N Ratio >118dbChannel separation >115dB 1khz <div style="text-align:center"><a style="text-decoration:none" href="http://mostpopular.sellathon.com/?id=AC1076765"><img src="http://www.sellathon.com/Resources/Images/countercredit.gif" border="0"></a></div>
Price: 24999 USD
Location: Ocala, Florida
End Time: 2024-08-23T10:36:21.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
Brand: Critical Mass
RMS Wattage: 1000
Model: ELS-1000.2 pls 3way 6.5 1ohm Front Stage
Country of Manufacture: United States
MPN: ELS-1000.2 pls 3way 6.5 1ohm Speaker set
RMS Power: 1000W
Country/Region of Manufacture: United States
Channels: 2
