Amplifier keying relay buffer interface for ICOM Kenwood and Yaesu FT-2000

Description: This listing is for the RBI-2A interface, cables for Kenwood radio * and Yaesu FT-2000 or ICOM radio ** to one or two amplifiers Includes RBI-2A, DC cable and plug, ONE 7 pin Kenwood * cable and THREE RCA-RCA cablesKenwood 7 pin goes in appropriate rear panel jack for compatible Kenwood * RCA cable goes to FT-2000 "TX GND" jack on rear panel or ICOM ** "RELAY" or "SEND" jack The other two RCA-RCA cables are to go from RBI-2A to amplifiers "RELAY" jack All cables are 5-6 feet long *compatible with Kenwood radios: TS-2000 HF (not VHF/UHF, see our other listings) TS-830, TS-850, TS-870TS-930, TS-940, TS-950TS-120, TS-130, TS-140, TS-180TS-430, TS-440, TS-450, TS-480 TS-530, TS-570, , TS-590, TS-990 TS-680, TS-690** Compatible ICOM radios ICOM radios with rear panel SEND or RELAY RCA jacks, IC-718, IC-7200, IC-756, IC-756PRO, IC-756PRO2, IC-756PRO3, IC-7600, IC-7410, IC-7700, IC-7800, IC-7850, IC-9100 IC-78, IC-725, IC-726, IC-728, IC729, IC-730, IC-735, IC-736, IC-737, IC-737A, IC-738, IC-740, IC-745, IC-746, IC-746PRO, IC-751, IC-751A, IC-761, IC-765, IC-775DSP, IC-781 AND MAYBE MORE, you must check your radio model rear panel for an RCA jack labeled "SEND" or "RELAY" if not listed here.TWO radios keys TWO amplifiers with bypass switch High quality relay box to interface between any TWO radios and will key any TWO amplifiers Switch chooses ONE of TWO radios that will activate BOTH amplifiers or noise cancelling units or choose center switch position to bypass the amplifiers Many newer radios can only provide for a small amount of current on the external amplifier keying output.Better SAFE than SORRY! In response to your requests for a relay interface box that will key TWO completely separate amplifiers, we have developed the RBI-2a. Do you have a need to key TWO amplifiers (perhaps a driver amp and high power amp) that have two different keying relay voltages? Our RBI-2 can (for example) key one amp with a 120 VAC T/R relay and your other amplifier that uses a 12 VDC T/R relay (or ANY voltage and current up to 240 volts ac/dc @ 5 amps for EACH amp). The keying circuits in our RBI-2a are COMPLETELY SEPARATE from each other and the radio is isolated. EACH output is a relay closure from center conductor of the RCA jack to the outside of the RCA jack. EACH output uses a completely SEPARATE relay! WHY use two amplifiers? Some users want to extend the life of their radio's expensive final transistors by running low power from their radio into an intermediate amplifier and have that amplifier run only what is needed to get full output from their higher power amplifier. Some users want to use an "instant on" amplifier for most contacts but still also have a larger amplifier what may require warm up time that is less frequently used. With our box, you do not need to reach in back to disconnect and reconnect each amplifier keying line. Some users have dedicated amplifiers for different bands and antennas and also don't want to to disconnect and reconnect individual relay keying cables Our box will draw <1 MA from your radio and will key any TWO separate amplifiers. A very handy accessory. Get one BEFORE you damage your radios amplifier keying output! RCA jacks in and out Needs 9-15 VDC at only 65 ma. 5 feet of wire and 2.1 x 5.5 mm universal DC connector included Connect our RBI-2A to your radios keying circuit (ground center conductor to key our box) Connect your amplifier relay keying input to either output on our RBI-2A, connect your other amp keying line to the other RBI-2a output Relays rated up to 240 Volts at 5 AMPS, switch AC or DC any polarity! Genuine relay used for switching (not an easy to damage solid state device) Both amplifiers switch at the same time Both amplifier keying lines are completely isolated from each other BYPASS switch (amplifiers are not keyed by either radio) See separate ebay listing for RCA-RCA male connector cables 100% hand made and tested by Hams for Hams in Colorado This is not one of those types that make you use a battery to power the unit! This high quality device is powered by your station power supply or any filtered DC source from 9-15 VDC (only 65 ma required) Need the best DC power supply? See our ebay store for SAMLEX power supplies. Need to key only one amplifier? See our eBay store listing for the RBI-1 amplifier keying relay interface Need to key up to SIX amplifiers? See our eBay store listing for the RBI-6a amplifier keying relay interface Need to key MORE than two linears? Contact us for custom made amplifier PTT relay keying interfaces. (We just finished a SIX unit amp keying box, keyed from a single radio) When connecting your Radio and Amplifier, there may be switching voltage, polarity, and current incompatibility that can cause damage to your radio or amplifier if connected without a switching interface between them. Even if your internal radio switching looks like it might be usable, it is wise to have an extra degree of isolation between your amplifier and radio with our relay buffer interface. 73, Dan W7RF ( Radiodan ) Ham Radio linear amplifier amateur amatuer radio interface relay keying Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.

Price: 79.95 USD

Location: Fort Collins, Colorado

End Time: 2024-02-05T23:36:27.000Z

Shipping Cost: 6.95 USD